MRCOOL DIY vs Olympus E Star: What's the Difference?

MRCOOL DIY vs Olympus E Star: What's the Difference?

Quick answer: The MRCOOL DIY 5th Gen is made for homeowners to install. It ships with a 25 ft pre-charged QuickConnect line set, so you skip the vacuum pump. The Olympus E Star is a pro install system with flare fittings and a vacuum step. The E Star 9K has a higher SEER2 rating, and both heat below zero.

Both lines come from MRCOOL, and both are ductless heat pumps that heat and cool. The big difference is who puts them in. This guide compares install, efficiency, cold weather heating, noise, power, and warranty side by side, so you can pick the right one before you buy. Every number comes from MRCOOL manuals, MRCOOL spec sheets, or Chill product pages.

MRCOOL DIY 5th Gen vs Olympus E Star infographic comparing installer, line set, vacuum step, SEER2, lowest heating temperature and voltage

What is the difference between MRCOOL DIY and Olympus E Star?

The MRCOOL DIY 5th Gen is built for a homeowner install. Chill's product pages say it comes with a 25 ft DIY QuickConnect line set that is pre-charged with R-454B refrigerant. That means no vacuum pump. The pages also say it needs no special tools or prior experience.

The MRCOOL Olympus E Star is MRCOOL's pro install single zone line. Its 2025 install manual says installation must be done by a specialist, and that a qualified electrical technician must do the electrical work. It uses flare fittings. The installer pulls a vacuum on the lines to 500 microns before the system runs.

Not every MRCOOL system is DIY. For a look at the full MRCOOL lineup, see our guide to whether MRCOOL is a good brand.

How do the DIY 5th Gen and Olympus E Star compare side by side?

Feature MRCOOL DIY 5th Gen MRCOOL Olympus E Star
Who installs it Homeowner Licensed pro where required
Line set 25 ft pre-charged QuickConnect, included Flare fittings, line set sold separately
Vacuum pump needed No Yes, to 500 microns
SEER2 (9K / 12K / 18K / 24K) 23.6 / 23.5 / 22.5 / 22.7 27.4 / 25.4 / 21.4 / 21.0
Lowest outdoor heating temp -13°F (Hyper Heat models: -22°F) -22°F (current models ending in 230C-O1)
Quietest indoor setting 18 to 20 dBA 16 to 19.5 dBA
Power 115V (9K, 12K), 230V (18K, 24K) 208/230V, all sizes
Base warranty 5 year parts, 7 year compressor 5 year parts, 7 year compressor when registered and pro installed

Sources: Chill product pages for the DIY 5th Gen and Olympus E Star, the MRCOOL 5th Gen DIY manual, the MRCOOL Olympus E Star install manual, and the MRCOOL Olympus E Star submittal sheet.

Which one is more efficient?

It depends on the size. SEER2 measures cooling efficiency, and a higher number is better. At 9K and 12K, the Olympus E Star rates higher, with 27.4 and 25.4 SEER2. At 18K and 24K, the DIY 5th Gen rates a bit higher, with 22.5 and 22.7 SEER2.

For heating, the E Star 9K lists 12.5 HSPF2 (region IV). The DIY 5th Gen 9K lists 11.5. Our SEER2, HSPF2 and COP guide explains what these ratings mean.

Which one heats better in cold weather?

MRCOOL's DIY manual lists heat mode down to -13°F outside for the standard DIY 5th Gen. MRCOOL's current E Star submittal sheet lists a heating range of -22°F to 75°F outside for the 9K, 12K, 18K and 24K. Those are the current models, with outdoor unit numbers ending in 230C-O1. MRCOOL support lists older E Star models ending in 230B at -13°F, so match the model number to the spec sheet.

Want a DIY system that heats in that kind of cold? The MRCOOL DIY Hyper Heat systems also heat down to -22°F, per their Chill product pages and MRCOOL's Hyper Heat manual. That matches the current E Star. Our cold climate comparison compares Hyper Heat with the standard 5th Gen.

What does each system need for power and install?

Power. The MRCOOL DIY 9K 5th Gen and DIY 12K 5th Gen run on 115V. The larger DIY sizes and every Olympus E Star run on 208/230V. Our 115V vs 230V guide covers breakers and wiring.

Install. The DIY 5th Gen still takes real work. MRCOOL's manual lists open ended or adjustable wrenches for the line set nuts and a 3.54 inch core drill for the wall hole. See what comes with a MRCOOL DIY mini split and can you install a MRCOOL DIY yourself before you buy.

The E Star manual adds steps a DIY kit skips. The installer makes flare connections, tightens them with a torque wrench, and runs a vacuum pump with a micron gauge. The E Star manual lists a 9.84 ft minimum line length. It also lists a maximum of 82 ft for the 9K and 12K and 98.4 ft for the 18K. Measuring your route first? Use our line set length guide.

Which size do I need?

Both lines come in 9K, 12K, 18K, and 24K single zone sizes. Size the room first. Our mini split sizing guide walks through square feet and BTU. For a whole home or a main living space, run our free Manual J calculator.

Then compare models in the same size. Two E Star examples are the Olympus E Star 9K and the Olympus E Star 18K.

Still shopping?

See every DIY size in our MRCOOL DIY 5th Gen mini splits collection, or browse the MRCOOL Olympus collection for pro install systems. Want help choosing between them? Call Chill Mini Splits at (888) 231-8920.

FAQ

Can I install a MRCOOL Olympus E Star myself?

MRCOOL's E Star install manual says a specialist must do the install, and a qualified electrical technician must do the electrical work. Chill's E Star pages say the 5 year parts and 7 year compressor warranty applies when the system is registered and installed by a licensed professional.

Is the Olympus E Star more efficient than the MRCOOL DIY?

At 9K and 12K, yes. The E Star lists 27.4 and 25.4 SEER2, compared with 23.6 and 23.5 for the DIY 5th Gen. At 18K and 24K, the DIY 5th Gen lists slightly higher SEER2.

Does the Olympus E Star come with a line set?

No line set is shown in the E Star manual's packing list. The manual says items not included must be bought separately. The DIY 5th Gen includes a 25 ft pre-charged QuickConnect line set.

Which is better for very cold winters?

MRCOOL's current E Star submittal sheet lists heating down to -22°F for models ending in 230C-O1. Older E Star models ending in 230B are listed at -13°F. The standard DIY 5th Gen heats down to -13°F, per its manual. MRCOOL DIY Hyper Heat models also heat down to -22°F, the same as the current E Star.

Is the Olympus E Star quieter than the MRCOOL DIY?

The quietest settings are close. Chill's pages list 18 to 20 dBA for the DIY 5th Gen indoor units. MRCOOL's E Star submittal sheet lists 16 to 19.5 dBA for the E Star indoor units on their lowest setting.

Do the MRCOOL DIY and Olympus E Star need 230V power?

Every Olympus E Star runs on 208/230V. The MRCOOL DIY 9K and 12K 5th Gen run on 115V, and the 18K and 24K run on 230V.

Who can answer install questions about my MRCOOL unit?

MRCOOL tech support can help with install and setup questions at 270-366-0457. You can also find each full install manual on MRCOOL's site.

Ready to size your system?

Use the calculator for a quick match, or build a complete multi-room system with live pricing.

Keep learning